Ham Radio Station AC2C

[HL2UOK]

Ham Radio Station AC2C Hex Beam Information

Home Page My Ham Career Photo Album Hex Beam Info Key Collection DX QSL Cards Favorite Links

This page contains some photographs and descriptions of the construction of my 6-band Hex Beam. Please note that each image on this page is linked to a larger (1600 x 1200 pixel) image. Smaller images are displayed here to enable faster loading. Clicking on any image will result in a 1600 x 1200 pixel image opening in a separate browser window. Leo Shoemaker, K4KIO, maintains an outstanding website that contains step-by-step construction details. Leo's site and instructions were my constant companion throughout the construction. I will not even pretend to provide the level of detail that Leo provides, but did want to post some pictures of what I did and what I learned during my project. In my opinion, the most important and most critical part of the construction project is the construction of the "Base Plate". The Base Plate is the part of the Hex Beam that acts as a hub, or spoke, to hold the spreader arms and also attaches the entire antenna to the mast. Various materials have been used to construct base plates and I suspect that the most enduring material would be aluminum. In my case, however, I selected to make mine out of wood and seal it well with several coats of good quality paint. I started with a 10-1/2" wide board and cut two maximum diameter circles. The two circles were then glued back-to-back and allowed to dry for a few days before continuing. Once the base plate material is identified and cut to size, the next essential step is to determine the position of each of the six spreader arms. The six arms need to be spaced exactly 60-degrees apart. There are various ways of completing this task, but I found it very easy to create a perfect hexagon on my PC, print it out, and use it as a template. Once the template was "pinned" to the center of the circular base plate, a few lines drawn with a sharpie pen created the six lines required. Once the lines are drawn to identify where the spreader arms will be attached, the next step is to drill a hole for the center support post. One of the most popular construction materials for the center post is thick-wall PVC pipe available at most local hardware stores. I drilled the center post hole with a hole saw that was just slightly smaller than the center post and then slowly hand sanded the hole to provide for a very tight fit between the base plate and the center pole. There are about as many ways to attach the spreader arms to the base plate hub as there are ways to make a base plate. The three basic concepts are: (a) Attach the spreader arms directly to the base plate; (b) Provide a hollow tube into which the spreader arms can slide; or (c) Provide a rod onto which the hollow spreader arms can slide. I borrowed an idea from Leo Shoemaker, K4KIO, to have the spreader arms slightly angled upward. My experience in building two Hex Beams is that the actual bend shape is quite crucial. Since the different length elements are strung between the bent spreader arms, one common problem in Hex Beam stringing is that the higher frequency (shorter length) elements tend to end up being very close to each other and cause unwanted interaction and detuning. Leo's idea was to provide the spreader arms with a slight upward angle at the very base and hope the the 12M and 15M elements would have some additional separation. I attached the base plate to the center post using three 3-inch x 3-inch "L" brackets from the local Ace Hardware Store. A few more coats of glossy black paint and the antenna construction is ready to start. From personal experience, I strongly recommend a very modular approach throughout the entire construction process - always leave yourself an option of changing any particular piece later on. In this specific design, for example, I found that the wooden dowels as spreader support arms was a bad decision. Within two months of being in the air, the wooden dowels had absorbed moisture trapped in the fiberglass spreaders and rotted. Luckily, it was a relatively easy repair that was completed without the need to even lower the antenna to the ground. From the rooftop, I was able to detach one spreader at a time and replace the wooden dowel with a metal tubing made from 3/4-inch EMT conduit. The fiberglass easily slipped over the EMT conduit and all six spreader spokes were replaced during a single weekend project. Once the baseplate is completed, the Hex Beam construction project is far more than half complete. It's now time to move the project outdoors - you will need an area at least 20 feet in diameter that is clear of all obstructions. Both of my Hex Beams have been constructed in my back yard. I start with a very strong post solidy planted in the ground that serves as the antenna mast during construction. Once the base plate is mounted to the temporary mast, the fiberglass spreaders are attached to the base plate and precisely cut lengths of dacron rope are used to form the six spreaders into the "inverted umbrella" shape. The process of doing this is very well documented on Leo Shoemaker's website and I can not imagine stringing the elements without first using Leo's method to form the basic shape. I used a total of twelve (12) dacron ropes pieces, each 124" in length. Six peices are used to tie each spreader end to the top of the center post. Six more pieces are used to tie each spreader end to the two adjacent spreader ends. The twelve pieces of dacron rope form a perfect hexagon and hold the spreader in the proper shape for threading the wires that make each element. As mentioned previously, one common problem with multi-band Hex Beams is that sometimes elements for adjacent bands end up being too close together and result in undesirable interaction and detuning. The most common elements involved in this problem are the 12M and 15M elements. In nearly all Hex Beam designs what happens is that the parabolic shape of the bent spreader arms results in a lower slope angle close to the base plate and a larger slope angle near the top. As a result, when stringing wire between the center post and the spreader arms, the shorter-length elements (located further down the center post) tend to have very little vertical separation. If you've ever strung wires in a Hex Beam, you will immediately understand the dilemma, if not, you may have to visualize the "inverted umbrella" shape or study some of Leo's diagrams. I ran into this problem with my first Hex Beam and stopped stringing elements after stringing the 20M, 17M, and 15M wires. In my second Hex Beam, I wanted to find a solution to this problem. After conferring with Steve Hunt, G3TXQ, I decided to try what I believe to be a unique approach to solving the problem. I asked myself "why do I have to run the wires all the way to the spreader arm? What if I strung each wire at the desired vertical position and just suspended the elements within the parabolic frame using dacron rope to tie the element knees and ends to the closest spreader arm?" Click on the picture to the right for an exploded view of the suspended elements. The result worked well for me. The 20M, 10M, and 6M elements are strung between the center post and the spreader arms and the 17M, 15M and 12M elements are suspended within the parabolic shaped frame. Each band tunes to a reasonable SWR and on air testing shows a reasonable front to back ratio. My main recommendation once you get to this point is patience, patience, patience. Use temporary methods to attach the various element wires to the center post and the spreader arms. Once you get the adjustments "close", then start moving an inch or so up, down, in, out and keep making sure each element is fairly straight and level. It takes a while, but patience really pays off. Once you get the entire structure fine tuned and tweaked just right, it's time for the final assembly. The elements need to be permanently attached to the center post - this method also is copied from K4KIO's step-by-step instructions. Once the elements are connected to the center post, the final step is to interconnect each set of elements to a common feedline. This Hex Beam is fed at the top 20M element with good quality RG-8 Coax. The final step was to put the completed Hex Beam about 10 feet above ground and fine tune each band. I found it easy to slip the Hex Beam atop an unused 10' section of aluminum tower and work on the elements from the comfort of my back deck. I used a 5-foot step ladder to work on the upper elements. Steve Hunt, G3TXQ, has done more modeling and experimenting with Hex Beam tuning methods than anyone else that I have run across. Steve's advice was essential to me throughout the final tuning steps. Here is the completed Hex Beam waiting for me to find the right weather to carry it up to the rooftop where it would sit atop a mast. Note a 1:1 coax balun made from about 10 wraps of coax in a 6 inch diameter. My experience with the Hex Beam has been very pleasant. It stands up well to both summer and winter weather and storms and is easily rotated with a light weight rotator. Return to Photo Album Page