Quadrature detector

[라디오]

http://www.techonline.com/community/ed_resource/feature_article/14378

TechOnLine > Educational Resources > Feature Articles

Welcome, Guest | My Archive | Log In

                                          Worse | Better  

Rate This Article

   Add Comments           1      2      3      4      5

TechOnLine Publication Date:  Jun. 4, 2001

A Quadrature Demodulator Tutorial Danielle Coffing and Eric Main Motorola

	ABOUT THE AUTHORS Danielle Coffing joined Motorola Semiconductor Products Sector in Tempe, AZ in 1997. Since then, she has worked in the area of high-frequency analog integrated circuit design and development. She holds one patent and has seven pending. She received her BSEE and MSEE degrees from the Massachusetts Institute of Technology in 1996 and 1997, respectively. Eric Main joined Motorola Semiconductor Products Sector in 1970. Since then, he has worked in the area of analog integrated circuit design and development. He received his B.Sc.(Eng) in electrical engineering from the University of Aberdeen, Scotland in 1965. He holds 41 patents and has seven pending.

In an FM signal, the modulation is the deviation of a carrier from its nominal frequency. The conventional method to demodulate this signal is to convert frequency deviation to phase and detect the change of phase. In the quadrature demodulator, the modulated carrier is passed through an LC tank circuit that shifts the signal by 90° at the center frequency. This phase shift is either greater or less than 90° depending on the direction of deviation. A phase detector compares the phase-shifted signal to the original to give the demodulated baseband signal. You use quadrature demodulators not only for frequency modulation, but also with digital modulation schemes such as FSK (frequency shift keying) and GFSK (Gaussian frequency shift keying).

FM Quadrature Demodulator Block Diagram

The conventional method of FM demodulation for integrated circuits is Bilotti's quadrature demodulator that uses a phase shift network and a phase detector . Figure 1 shows the block diagram of this quadrature demodulator. The phase detector compares the phase of the IF signal (v₁) to v₂, the signal generated by passing v₁ through a phase shift network. This phase shift network includes an LC tank (L, R_p, and C_p) and a series reactance (C_s). The network gives a frequency-sensitive 90° phase shift at the center frequency. The phase detector discussed here is the bipolar double-balanced multiplier popularized by Bilotti . The output of the multiplier (I_o) is filtered, which results in a DC level that changes as the input frequency changes.

Figure 1:  Quadrature demodulator block diagram

Quadrature Demodulator Transfer Function

To derive the transfer function of the quadrature demodulator, the phase shift network is first drawn as a small-signal circuit model (Figure 2). The impedance (Z_p) of the parallel combination of L, R_p, and C_p is:

Figure 2:  Small-signal model of the quadrature phase-shift network

The ratio of v₂ over v₁ is the ratio of impedances Z_p(s) over (Z_p(s) + 1/sC_s). Simplifying this ratio,

The resonant frequency _n of this filter is:

The quality factor Q of the phase shift network is R_p/( _nL). Next, Equation 2 is used to solve for the transfer function from v₁ to v₂. The variables _n and Q are substituted into Equation 2 and v₂/v₁ is written in terms of s=j where _n:

In Equation 4, is the deviation from the carrier frequency, and 2Q / _n is the normalized deviation. Defining:

Equation 4 can be written as:

Writing v₂ in terms of v₁,

Equation 7 describes the signal at one multiplier input in terms of the signal at the other input. The signal v₁ is applied to the first input and is in limiting (a square wave). The signal at the second input (v₂) is a linear signal. By integrating over half of the period, you get the average value of the multiplier output current:

For a bipolar differential amplifier, g_m is I_o/V_T where 2I_o is the multiplier bias current. Substituting for v₂ and g_m,

where V₁ is the peak voltage of the signal v₁. Simplifying Equation 9 yields the transfer function for the quadrature demodulator:

In Figure 3, the term a/(1+a²) from Equation 10 is plotted versus the normalized frequency deviation (a). This plot is the quadrature demodulator s-curve. As the frequency of the signal applied to the demodulator becomes more positive than the natural frequency of the phase shift network, the filtered output of the multiplier increases. Likewise, the filtered output decreases as the frequency of the input signal decreases.

Figure 3:  Plot of normalized demodulator output vs. normalized frequency deviation

Integrated Circuit Implementation

Figure 4 shows an integrated circuit implementation of the quadrature demodulator. The input signal v_in is supplied from a limiting amplifier and is a square wave of known amplitude. The input signal v_in is level shifted, and v₁ is applied to transistors Q₁ and Q₂. The amplitude of v₁ is large enough such that Q₁ and Q₂ are switched completely on or off during each cycle. Capacitor C_s is typically integrated while C_p, L, and R_p are external components. The component values are chosen such that the amplitude of v₂ is less than that of v₁ as given by Equation 7. This causes transistors Q₃-Q₆ to operate as linear devices rather than switches. The output of the multiplier is converted from a differential current to a single-ended voltage v_o. The output is filtered by components R_f and C_f.

Figure 4:  Integrated circuit implementation of the quadrature demodulator

The authors gratefully acknowledge Mark Randol.

                                          Worse | Better  

Rate This Article

   Add Comments           1      2      3      4      5

TOOLS

	Printer Friendly
*	Email a Friend

RESOURCES

P	Most Popular Feature Articles
C	Highest Rated Feature Articles

RELATED CONTENT

Feature Article
	Bluetooth RF System-on-Chip: Product Design Challenges and Tradeoffs Andreas Sibrai and Vjekoslav Matic Dialog Semiconductor

Course
	Quadrature Demodulator Tutorial

RELATED COMPANIES

Freescale Semiconductor

Home | Site Map | Prefs | FAQs | About Us | Contact Us | Tech Groups | Product Eval‎uation | Ed Resources | Tech Topics | Company Directory
Privacy Statement | Terms and Conditions | EE Times | EE Times International Sites | CMP Media
Audio DesignLine | Automotive DesignLine | Digital TV DesignLine | Embedded.com | Industrial Control DesignLine
Mobile Handset DesignLine | Network Systems DesignLine | Planet Analog | Power Management DesignLine
Programmable Logic DesignLine | Video/Imaging DesignLine | Wireless Net DesignLine
Copyright 1996 - 2006 TechOnLine, Bedford, MA, All Rights Reserved.

[라디오]

implementation=구현,이행

[라디오]

A. Bilotti, "FM Detection Using a Product Detector," Proceedings of the IEEE, pp: 755-757, Apr. 1968.

[라디오]

A. Bilotti, "Applications of a Monolithic Analog Multiplier", IEEE Journal of Solid-State Circuits, vol. SC-3, no. 4, pp. 373-380, Dec. 1968.