<P>이것을 구해 볼려고 국내 업체를 알아보았는데 취급하는데가 없네요.</P>
<P>이베이에서는 팔던데.. 가방끈이 짧아서 ㅠㅠ</P>
<P> </P>
<P> </P>
<P>Photocopy or Laser Print circuit image onto the dull side (emulsion) of Press-n-Peel Image Transfer Film. </P>
<P>Prepare: Clothes Iron, Steel Wool #00 (or SOS/Brillo with all the soap washed out), Packaging Tape,Photocopy or Laser Printed Circuit Image, & Directions </P>
<P style="TEXT-ALIGN: center">
<IMG alt="Prepare Press-N-peel" src="https://img1.daumcdn.net/relay/cafe/original/?fname=http%3A%2F%2Fwww.techniks.com%2Fimages%2FMvc-002f.jpg">
<IMG alt=Press-N-peel src="https://img1.daumcdn.net/relay/cafe/original/?fname=http%3A%2F%2Fwww.techniks.com%2Fimages%2FMvc-004f.jpg"> </P>
<P>Cut Press-n-Peel, leaving a 1/4" border around the circuit image. Cut board to size. Clean copper board with steel wool, S.O.S. or Brillo pads. Rinse cleaned board with soap and water. Be sure to remove all soap residue. Dry thoroughly with lint-free cloth. Be sure to scrape any burrs that appear on the edge of the board that may have resulted from the cutting/shearing process. Burrs tend to keep the iron from making solid contact with the Press-n-Peel Film </P>
<P style="TEXT-ALIGN: center">
<IMG alt="Clean copper board" src="https://img1.daumcdn.net/relay/cafe/original/?fname=http%3A%2F%2Fwww.techniks.com%2Fimages%2FMvc-007f.jpg">
<IMG alt="Cut Press-N-peel" src="https://img1.daumcdn.net/relay/cafe/original/?fname=http%3A%2F%2Fwww.techniks.com%2Fimages%2FMvc-003f.jpg"> </P>
<P>Place Press-n-Peel with image face down onto clean copper board. Iron the Press-n-Peel Film to the board a peice of plain paper between the iron and the film to reduce friction. Temperature setting on the iron is critical, and dependant upon your laser printer or photocopier. Suggested starting temperature is 275-325 degrees F. Iron setting is generally "polyester". Iron temperatures vary. Iron until board has completely and fully reached the temperature of the iron. Time varies with the size and thickness of the board. Generally this is 1.5 to 10 min. DO NOT USE THE STEAM SETTING! </P>
<P style="TEXT-ALIGN: center">
<IMG alt="Place Press-N-peel" src="https://img1.daumcdn.net/relay/cafe/original/?fname=http%3A%2F%2Fwww.techniks.com%2Fimages%2FMvc-005f.jpg">
<IMG alt="Iron Press-N-peel" src="https://img1.daumcdn.net/relay/cafe/original/?fname=http%3A%2F%2Fwww.techniks.com%2Fimages%2FMvc-008f.jpg"> </P>
<P>Quench the board/film combination under cold running water. Peel the film off. </P>
<P>To remove small "fills" in between traces and "filled donuts", cover the imaged copper board with clear packing tape, and then remove. This will pull all unwanted filled areas off the board. </P>
<P style="TEXT-ALIGN: center">
<IMG alt="Peel the film off" src="https://img1.daumcdn.net/relay/cafe/original/?fname=http%3A%2F%2Fwww.techniks.com%2Fimages%2FMvc-012f.jpg"> </P>
<P>After removing "fills", trim the board (if necessary) to the final size. Wash the board in soap & water before etching to remove surface oxidation. Etch with Ferric Chloride (Note: Techniks does not sell PCB etching supplies -- available through local electronic supply stores & Radio Shack) </P>
<P style="TEXT-ALIGN: center">
<IMG alt="Trim the PCB" src="https://img1.daumcdn.net/relay/cafe/original/?fname=http%3A%2F%2Fwww.techniks.com%2Fimages%2FMvc-013f.jpg"> </P>
<P>Using steel wool, scrub the Press-n-Peel image off as to reveal copper traces. This is best done under running water. Suggestion: Do not do this until your ready to drill and populate the board. The Press-n-Peel transfer resist protects the board from oxidation. </P>
<P style="TEXT-ALIGN: center">
<IMG alt="Scrub Press-N-Peel Image off" src="https://img1.daumcdn.net/relay/cafe/original/?fname=http%3A%2F%2Fwww.techniks.com%2Fimages%2FMvc-020f.jpg">
<IMG alt="The PCB" src="https://img1.daumcdn.net/relay/cafe/original/?fname=http%3A%2F%2Fwww.techniks.com%2Fimages%2FMvc-019f.jpg"> </P>
<P style="TEXT-ALIGN: center"> </P>
<P style="TEXT-ALIGN: center"> </P>
<P style="TEXT-ALIGN: center"> </P>
<P style="TEXT-ALIGN: center"><A title="[http://www.techniks.com/how_to.htm]로 이동합니다." href="http://www.techniks.com/how_to.htm" target=_blank>http://www.techniks.com/how_to.htm</A></P>
<P style="TEXT-ALIGN: center"> </P>
<P style="TEXT-ALIGN: center"><A title="[http://www.dipmicro.com/store/index.php?act=viewProd&productId=612]로 이동합니다." href="http://www.dipmicro.com/store/index.php?act=viewProd&productId=612" target=_blank>http://www.dipmicro.com/store/index.php?act=viewProd&productId=612</A></P>
<!-- -->
아래 싸이트에서 판매합니다만 회원가입을 해야 내용을 볼 수 있습니다. 장사하는 싸이트가 왜 그러는지... 한 장에 2000원이랍니다. http://bornagin.net/zeroboard/zboard.php?category=10&id=partsdb&page=1&page_num=7&sn=off&ss=on&sc=on&keyword=&select_arrange=headnum&desc=asc&PHPSESSID=f3dd929303fdf861af667a00ffebbf7c
첫댓글 간단하게 폭좁은 것이라면 단면 접착성 테이프인데
투명 스티카 처럼 떼어서 붙이는 것이군요.
구글 크롬을 다운로드 받아서 붙여 넣기 하시면 어색한 번역이지만 번역되지요
아래 싸이트에서 판매합니다만 회원가입을 해야 내용을 볼 수 있습니다. 장사하는 싸이트가 왜 그러는지...
한 장에 2000원이랍니다.
http://bornagin.net/zeroboard/zboard.php?category=10&id=partsdb&page=1&page_num=7&sn=off&ss=on&sc=on&keyword=&select_arrange=headnum&desc=asc&PHPSESSID=f3dd929303fdf861af667a00ffebbf7c
쉽게 배울수 있는 PCB 캐드는 어떤게 있나요?, 옛날에는 손으로 그려서 했는데, 지금은 컴퓨터로 하는 것이 맞는 것 같습니다만,....
가장 쉬운 것으로는 아마 eagle 일겁니다. 프로그램도 가볍고... pcb아트웍을 전문으로 할 목적이 아니라면 강추입니다.
( http://cadsoftusa.com/ )
삼족오님 감사합니다. 프리웨어 버전으로 다운로드 중입니다. 열심히 공부 해 보겠습니다
시험판이어서 기판 크기의 제한때문에 불편하시면 쪽지 한번 주세요.