Hobbywing Platinum 50A/100A V3 거버너 설정하기 (Store 모드)
I. 제일 먼저 변속기 "Heli Governor Off" 로 설정하시고, 조종기로 변속기 High/Low 컬리버레이션 후 전원 Off.
(노멀 쓰로틀 곡선: 0-25-50-75-100)
II. 전원 재연결 후 이전 설정 상태가 반드시 "Heli Governor Off"여야 하며, "Heli Governor Store" 모드로 설정 변경 후에 전원 Off.
전원 재연결 후 쓰로틀 50% (로터낀 상태로 피치 중립 위치)으로 올린후 RPM 증가가 멈춘 상태에서 최소 11초 동안 RPM을 인식시켜 줘야 하며, 이때 헬기는 안띄워도 됩니다.
(노멀 쓰로틀 곡선: 0-25-50-75-100)
III. 이제 쓰로틀 50%에서 RPM을 인식했으므로 Governor가 동작 가능한 상태이며, 변속기 전원을 빼고 다시 연결한 상태에서 원하는 헤드 스피드(RPM)가 나오는 적정 %의 쓰로틀 곡선을 그리시면 Governor가 동작될 것입니다. 예를들면, 쓰로틀 50% 부터 시작해서 RPM 측정기(타코메타)로 확인하면서 적정 RPM이 나오는 쓰로틀 % 찾아서 그 값으로 설정해서 날리면 됩니다.
(노멀 쓰로틀 곡선 예: 0-50-50-50-50 --> 0-55-55-55-55 --> 0-60-60-60-60)
쓰로틀은 최소 거버너 마진 15%(100-85=15%)인 85%까지 올려서 쓸 수 있구요, 만약 쓰로틀 90% 까지 올려도 원하는 RPM이 안나오면 모터 피니언 티수를 높이거나 Governor Off 로 그냥 날려야 됩니다. (95%까지 올려서 쓰시는 분도 있긴 합니다)
아래 설명 참고..
**Everyone needs to know, on the Platinum 50a v3 DO NOT RUN THE BEC AT 7.4 VOLTS!**
주의) 하비윙 V3 변속기 내장 BEC는 6V 로만 사용하세요. 7.4V 이상으로 설정하면 헬기가 이유없이 그냥 떨어짐..
Before we begin setting up the governor you will need to calibrate the ESC to your motor. Ensure that your transmitter has a full range of throttle 0-100 or -100->100 on the throttle channel using your transmitters monitor.
Here are the steps to calibrate the ESC:
1.(With all blades removed) move the stick on your transmitter to full throttle.
2. Power up your ESC and it will make a few tones.
3. Lower the stick to zero throttle and they ESC will tone again.
4. Disconnect power, throttle has now been calibrated.
Here are the steps to enable the Governor with Gov Store:
1. Plug program box into ESC program port and power up
2. Select "Gov Store" mode on the program box and press OK to save.
3. Power down the ESC, unplug program box again ensure ALL blades are removed. (로터는 빼고 할수도 있지만 끼고 설정하는게 좋음, 로터는 빼고하면 Gov 쓰로틀 곡선이 너무 낮아질 수 있음)
4. Set one of your Idle Up's to 50% throttle (쓰로틀 50% 일때 0 pitch가 되어야 함)
5. Fully charge your lipo pack
6. In a safe location power up the heli
7. Spool up the heli and switch to Idle Up 50%, the ESC will gradually provide full power. Once RPM stop rising let heli sit for at least 11 seconds, During this time the ESC will learn that is max RPM. Spool down. (쓰로틀 스틱 50% 올린 상태에서 더이상 RPM 증가가 멈춘 상태로 최소 11초 이상 고정 RPM을 지속시킨 후 RPM 인식시킨 후 쓰로틀 내림)
8. Disconnect power.
Once re-armed the ESC will remember max rpm and will utilize your throttle percentage based on that RPM. I recommend using Mr. Mels headspeed calculator to obtain your desired throttle percentage for each Idle up or use a tach.
If using a tach always start at a low percentage (IE 45%), tach and see if you are near your desired RPM, if not raise Idle up percentage a few points and tach again.
첫댓글 유용한정보입니다
네, 하비윙 거버너 설정은 정말 쉽습니다. RPM 유지를 위해 부하시에만 쓰로틀을 보전해 주기 때문에 배터리 런타임도 좋아집니다.
좋은 정보 감사합니다..