|
출처: 온로드 원문보기 글쓴이: [용산알씨]황국현85
Specification | XERUN-120A-V3.1 |
Current | Continuous: 120A, Burst: 760A |
Input * Note #1 | 4-9 cells NiMH/NiCd or 2-3S LiPo |
Built-in BEC | 6V@3A (linear mode) |
Resistance | 0.0003 Ohm |
Motor Supported | Sensored and sensorless brushless motor |
Suitable Motor | With 2 Lipo or 4-6 NiMH 1/10 on-road: >=3.5T, 1/10 off-road: >=5.5T With 3 Lipo or 7-9 NiMH 1/10 on-road: >=5.5T, 1/10 off-road: >=8.5T |
Suitable Car | 1/10,1/12 all competitions 1/10,1/8 rock crawler |
Cooling Fan | 5V |
Size | 37.5mm(L) * 31mm(W) * 29.5mm(H), excludes wire connectors 37.5mm(L) * 37mm(W) * 29.5mm(H), includes wire connectors |
Weight | 93g |
Features:
Specifications:
kV Without Load (RPM/V): 3000
Resistance: 0.0198
Input Voltage: 2-3S
Current Without Load (A): 2.4
Max. Output Power* (W): 265
Current @Max Output Power (A): 73
Motor Diameter x Length: 36x52.5mm
Shaft Diameter x Length: 3.175x14.6mm
Pole: 2
Weight: 180g
Application: 1/10 TC for stock racing
*The "Max. Output Power" is measured with 7.4V input voltage and ESC at ZERO timing. This parameter is neither the “maximum input power” nor the “rating power”, it is calculated by “RPM x Torque / 9550”
1. Setting or Updating the following ESC:
a) XERUN and EZRUN series Car ESC (Version 2.0 or later)
b) XERUN-120A V3 & V3.1 ESC
c) PLATINUM series helicopter/aircraft ESC
d) PLATINUM V3 series helicopter/aircraft ESC
2. Works as a Lipo battery voltmeter.
1 Working Modes
1.1 Works as an individual device to set the ESC, the value of each parameter is displayed on the LCD screen.
1.2 Works as an USB adapter to link the ESC with a PC to update the firmware of the ESC or set the ESC by HOBBYWING USB LINK SOFTWARE .
1.3 Works as a Lipo battery voltmeter to measure the voltage of the whole battery pack or each cell.
2 Specifications
2.1 Size: 90mm (L) * 51mm (W) * 17mm (H)
2.2 Weight: 65g
2.3 Input Voltage: 4.5-12.6V
(If the ESC hasn’t a built-in BEC, you must use an additional battery pack to supply the program box)
2.4 Displayer: 16*2 characters LCD.
2.5 Interface: Mini USB interface, ESC interface (Futaba plug), Power supply interface (Futaba plug)
3 Compared with the "2 in 1 Professional LCD Program Box"
Models of LCD program boxes:
2 in 1 Professional LCD program box (Already stopped)
Multifunction LCD program box: It is a new priduct uses MCU (microprocessor) with larger memory, it has a new function to work as Lipo battery voltmeter to measure the voltage of the whole battery pack and each cell.
a) Type A: The firmware with postfix “_V3” (eg. V1.11_120331_V3) is only suitable for XERUN-120A-SD V3 and V3.1 ESC
b) Type B: Firmware without postfix “_V3” (eg. V1.08_120504) is suitable for the ESC below except the XERUN-120A-SD V3 or V3.1 ESC.
(주)용산알씨 고객만족센터 : 02-711-0922
매장주소 : 서울특별시 용산구 청파로 74 전자랜드 신관 4층 406호