Victor(빅터) TT-801 + Ikeda IT-345 + CL-P1D 조합입니다.
원래는 별매품인 진공 펌프 까지 포함되면 좋겠지만 진공 펌프는 없습니다.
플린스도 Cabinet CL-P10 (¥ 75,000) 라는 모델이 있긴 하지만 아쉽게도 Cabinet CL-P1D (¥ 23,800) 에 장착되어 있습니다.
하지만 CL-P1D 만해도 아주 무겁고 아주 좋은 플린스 입니다.
아래는 제조사의 설명입니다.
Turntable unit pursuing the ultimate of no resonance and no vibration.
The turbo disk stabilizer system can be used by combining with the separately sold turbo disk stabilizer unit TS-1.
In the TT 801, we have succeeded in making the inside of the center spindle an air passage. The air sucked from the eight intake holes of the turntable mat passes through the slits on the turntable and the center spindle and is guided to the outside of the unit. The air is then exhausted from the TS-1, which is connected to the unit via a 2m suction pipe. This TS-1 continues to operate while the record is rotating, and a constant suction force is always applied, so that the vibration state of the record does not change and stable playback sound can be obtained. This constant suction method is based on the same principle as the stabilizer method used in the cutting race of the original record. In addition, since all the operation of the TS-1 is controlled by the TT 801 side, there is no need to worry about restriction of the installation location due to ON-OFF operation.
When the turbo disk stabilizer method is turned on, vibration generated in the middle and low frequencies is suppressed and vibration suppression effect of 20 dB or more is obtained. The relationship between the adsorption force of the stabilizer and the vibration characteristics of the record is measured. In order to obtain sufficient vibration suppression effect, the exhaust force of TS-1 is set to satisfy the adsorption force equivalent to 4 kg (70 mmAq).
The drive motor is equipped with a newly developed low-vibration DC motor that uses a coreless structure without cocking and achieves a torque of 2.5kg-cm. In addition, it uses a double servo quartz circuit with 30 times higher quartz lock stability than the conventional one and a synthesizer system, enabling precise pick control up to ± 9.9% in 0.1% steps.
In addition, it is equipped with a reset switch that can instantly return to standard speed.
The turntable is a composite structure of dissimilar metals, with a die-cast aluminum body and double zinc rings attached to it, resulting in 400kg-cm.2Large inertia mass has been realized, and unnecessary resonance such as the hanging rattle phenomenon has been eliminated.
Electronic brake quick stop mechanism using bi-directional servo with high rotational accuracy is adopted.
An electronic display tube, Digitron, is used for the speed and quartz lock indicator.
무공명, 무진동의 궁극을 추구하는 턴테이블 유닛.
터보 디스크 스태빌라이저 시스템은 별매품인 터보 디스크 스태빌라이저 유닛 TS-1과 결합하여 사용할 수 있습니다.
TT 801에서는 센터 스핀들 내부를 공기 통로로 만드는 데 성공했습니다. 턴테이블 매트의 8개 흡입구에서 흡입된 공기는 턴테이블의 슬릿과 중앙 스핀들을 통과하여 장치 외부로 유도됩니다. 그런 다음 공기는 2m 흡입 파이프를 통해 장치에 연결된 TS-1에서 배출됩니다. 이 TS-1은 레코드가 회전하는 동안 계속 작동하여 항상 일정한 흡입력이 가해지기 때문에 레코드의 진동 상태가 변하지 않고 안정적인 재생 사운드를 얻을 수 있습니다. 이 일정한 흡입 방식은 원곡의 커팅 레이스에 사용된 스태빌라이저 방식과 동일한 원리를 바탕으로 합니다. 게다가 TS-1의 모든 동작은 TT 801 측에서 제어하기 때문에,
터보 디스크 스태빌라이저 방식을 ON하면 중저역에서 발생하는 진동을 억제해 20dB 이상의 진동억제 효과를 얻을 수 있다. 안정제의 흡착력과 음반의 진동 특성 사이의 관계를 측정합니다. 충분한 진동 억제 효과를 얻기 위해 TS-1의 배기력은 4kg(70mmAq) 상당의 흡착력을 만족하도록 설정됩니다.
구동모터는 코킹이 없는 코어리스 구조를 채용한 신개발 저진동 DC모터를 탑재해 2.5kg-cm의 토크를 구현한다. 또한 기존 대비 30배 높은 쿼츠 잠금 안정성을 갖춘 더블 서보 쿼츠 회로와 신디사이저 시스템을 사용해 0.1% 간격으로 최대 ± 9.9%까지 정밀한 픽 제어가 가능하다.
또한, 즉시 표준 속도로 복귀할 수 있는 리셋 스위치도 탑재하고 있습니다.
턴테이블은 다이캐스트 알루미늄 본체와 이중 아연 링이 부착된 이종 금속의 복합 구조로 무게가 400kg-cm입니다. 2 큰 관성질량을 구현했으며, 매달리는 래틀 현상 등 불필요한 공진을 제거했습니다.
회전정도가 높은 양방향 서보를 이용한 전자식 브레이크 급정지 기구를 채용하였습니다.
속도 및 석영 잠금 표시 장치에는 전자 디스플레이 튜브인 Digitron이 사용됩니다.
첫댓글 첫 머리글에 설명하듯이 무공명, 무진동을 궁극의 목표로 한 기술과 스핀들 내부로 공기 통로를 만들어 외부로 배출, 레코드의 일정한 흡입력이 지속적으로 가해지는 기술등등이 엄청 들어간 고급 턴테이블이군요..^^
그 진공 흡착 장치는 아직 못 구했습니다, ㅠㅠ 물론 진공 흡착창치가 없어도 엄청난 반응속도와 정숙한 회전 특성등이 장점이긴 합니다.
@판돌이 무공명, 무공진 이 것만으로 이미 충분 조건을 갖추었다 할 수 있겠네요~
@록산 암튼 회전의 특성이나 동작의 정확성은 상당해 보이긴 합니다.