HEMP 공격은 무엇입니까? 아니, 그것은 당신의 앞 잔디밭에 냄비 흡연 히피족이 아니다. HEMP는 높은 고도 핵 전자기 펄스의 약자 EMP의 극단적 인 형태이다. 모든 충분히 강한 EMP는 우리가 많이 오늘날에 의존하는 민감한 전자가 손상 될 수 있습니다.
EMP의 근원
가장 일반적인 EMP는 번개에서 유래 및 장비 전원이 켜져하고 정상적인 전원 서지.태양 플레어와 같은 다른 자연적인 원인은 또한 EMP를 만들 수 있습니다. 1989 년 전체 퀘벡의 전기 그리드는 종료 된 인해 지구의 반대편에 히트 태양 플레어에 약 90 초.
마이크로 칩 현대 전자 나이가 가능한 트랜지스터 회로 다음에 가장 민감하다. 우리는 컴퓨터 및 기타 민감한 장비에 대한 서지 억제가 이유입니다. 그러나 대부분의 핵 EMP 공격에 대해 방어를하지 않을 것이다.
과전압에 의해 EMP 피해 전자. EMP는 그들이 호 및 고장 원인, 작은 집적 회로의 도체에 극단적 인 전압을 유도한다. 즉, 그들은 튀긴 얻는다.
무엇 많은 사람들이 기술의 발전으로 볼 수도 대마 공격에 우리가 더 취약합니다. 더 작고 더 정교한 전자 장치가 더 쉽게 EMP에 의해 손상 될 수 있습니다. 우리 사회는 커피 메이커에 대한 은행의 전력 그리드에 이르기까지 모든에 더 많은 전자 장치를 통합함에 따라, 인프라의 더 위험하다.
핵에서 HEMP의 위협은 번개보다 더 불길한 위험하다. 핵무기가 폭발 할 때, 그것은 "와 같은 확산은 매우 높은 EMP 생산 에너지의 벽 "과 수백 마일에 걸쳐 고체 전자 아무것도를 쓸어됩니다. 상업 서지 억제 및 대부분의 군사 등급의 유닛은 충분히 빨리 그것을 막을 수 없습니다. 전원 선은 콘센트에 연결되어 전력 그리드와 전자를 노크, 더욱 펄스를 수행하는 등 큰 안테나를 역할을합니다.
영화에서이 발췌 TRINITY AND BEYOND는 원자 폭탄 동영상은 곧 제한 핵 실험 금지 조약이 체결되기 전에 미국 군대에 의해 수행 약간 높은 고도의 테스트를 보여줍니다.그것은 예감, 드라마틱 한 음악과 함께 완료, 심지어 폭발 중에 절단 (시뮬레이션?) AM 라디오를 포함한다.
EMP 보호
그렇다면 당신은 EMP 공격에 대해 보호 할 수있는 방법이 있나요? 그것을 할 수있는 두 가지 방법이 있습니다 :
- EMP로부터 장비를 보호
- 그들이 EMP에 감염되지 않도록 전자 보안을 강화
차폐는 방어의 첫째 쉬운 라인입니다. 때로는 그 발명자 마이클 패러데이 후, 도전성 둘러싸인 차폐 실드의 내부에 그것을 제거하고 내용물을 보호 외부에 전하를 등화 것, 패러데이 케이지라고.
진정한 패러데이 케이지는 구리 또는 알루미늄 또는 적절히 설계 스틸 격납 같은 도전성 금속으로 이루어진다. 전자 레인지의 내부 패러데이 케이지 (Faraday cage)의 예입니다. 그러나 충분한 전자기 차폐 아연 도금 강판 또는 알루미늄 호일로 제조 될 수있다. 녹과 페인트 절연체이기 때문에 맨 손으로 또는 그린 스틸은 작동하지 않습니다.
대부분의 금고 및 파일 캐비닛은 EMP에 대해 보호하기 위해 작동하지 않습니다. 전체 컨테이너는 전기 경로에 휴식과 함께 도전해야합니다. 간격은 내부에 "누출"EMP 대부분의 컨테이너가 효과 만드는 것입니다. 하지만 (전자 레인지 도어의 화면처럼), 작동 미세 구멍과 메쉬 전도성 화면이나.
가장 쉬운 방법은 라디오 나 노트북 컴퓨터 같은 소형 전자 제품을 보호하기 위해, 다음, 무거운 의무 지퍼 잠금 냉장고 가방에 배치 무거운 의무 알루미늄 호일에 단단히 전체를 래핑하는 것입니다. 단단히 솔기를 접어 박의 틈새를 밀봉하고 EMP의 누출을 방지하기 위해 천공 않도록주의해야합니다. 두꺼운 호일 저항보다 눈물이지만, EMP 차단에 차이가 없습니다.
당신이이 권리를하는 경우, 각각의 하나의 층으로 작동합니다. 그러나 일부 추가 보험에 대한 더 많은 레이어를 추가합니다. 다른 냉동 가방 호일의 또 다른 레이어를 추가합니다. 각 계층은 당신이 완벽하게 밀봉하지 않는 경우 크게 EMP의 누출을 감소하는 데 도움이 될 것입니다. 그냥 확인 대체 레이어를합니다. 호일의 두 개의 층이 접촉되면, EMP 유도 전압은 단순히 외층 비효율적하게 내측으로 외부 층에서 전달된다.
누설에 대한 방패를 테스트
제대로 장치를 차폐되어 있는지 테스트하는 가장 쉬운 방법은 강력한 무선 신호로 조정 된 라디오를 보호하는 것입니다. 다음 단계별 지침입니다 :
정원 :
- 휴대용 AM / FM 라디오
- 배터리의 신선한 세트
- 라디오에 맞게 2 ~ 3 무거운 의무 냉동고 가방
- 내구성이 강한 알루미늄 호일.
또한 라디오 방송국에서 제공하는 강력한 무선 신호를해야합니다 (휴대폰과 같은 다른 무선 소스와 함께 할 것을 시도하지 않는다 -는 주 신호가 제대로 작동하지 않습니다 - 만약 당신이 킬로와트의 수십 이상을 원하는).
- 배터리를 설치 안테나가 완전히 (저장 위치) 붕괴되어 있는지 확인하고에 라디오를 켜십시오. FM 밴드와 함께 시작합니다.
- 조정 찾을 수있는 가장 강력한 FM 방송국의 라디오. 당신이 농촌 지역에 거주하는 경우, 당신은이 테스트를 할 역에 가까이해야 할 수 있습니다. 확인 신호가 안테나 아래로 크고 선명로 제공합니다.
- 당신이 호일 및 플라스틱 가방의 여러 레이어를 통해 라디오를들을 수 있도록 볼륨을 높입니다.
- 첫 번째 냉장고 가방에 라디오를 넣어 단단히 위에 가방을 접어 밀봉하십시오. 당신은 아직도 명확하게 FM 방송을들을 수 있어야합니다.
- 다음으로 체포 라디오 주위에 무거운 의무 알루미늄 호일의 단단한 층을 래핑합니다. 호일 시트는 두 배 이상 솔기를 접어 수있는 충분히 큰 있는지 확인합니다. 당신이이 권리를하는 경우에, 당신은 신호가 실질적으로 아무것도 내려 들려야합니다.
- 당신은 아직 명확하게 라디오를들을 수 있다면, 당신은 효과적으로 호일을 밀봉하지 않았습니다. 당신이 바로 그것을 얻을 때까지 다시 시도하고 틈이 없는지 확인합니다.
- 당신은 당신이 신호를 얻을 때까지 호일로 냉동 가방을 교대로 더 많은 레이어를 추가, 호일의 한 층을 보호 할 수없는 경우.
FM 방송국과 테스트를 수행 한 후, 떨어져 모든 것을 가지고 강한 AM 역으로 반복합니다. 당신은 동일한 결과 (신호 없음)를 받아야합니다. 그것은 그래서 당신이 더 많은 레이어를 추가해야하는 경우 낙심하지 마십시오 FM보다 AM를 보호하기 위해 더 열심히 할 수있다.
당신이 AM과 FM (순서는 중요하지 않습니다) 모두를 테스트해야합니다. 핵에서 EMP은 RF 스펙트럼에 걸쳐 광대역이므로 실제 조건의 더 나은 검사가 두 대역에 튜닝.
테스트를 수행 한 후, 모든 랩을 해제하고 다시 그것을 밀봉하기 전에 라디오에서 배터리를 제거합니다. 당신은 배터리가 누출 된 지금 라디오가 작동하지 않습니다 비상 사태에서 알 수 싶지 않아요.
EMP 강화 된 전자
당신이 정기적으로 라디오에 액세스해야한다면 당신은 무엇을 하는가? 분명히 당신은 당신이 매일 사용하는 경우는 호일에 싸여 원하지 않는다. 하나의 옵션은 단순히 하나 이상의 라디오를 구입하는 것입니다. 그러나 또 다른 옵션이 있습니다.
진공관 :이 솔루션은 기존 기술로 수 있습니다. 당신은 RCA 수리공을 기억만큼 나이 인 경우에, 당신은 아마 진공 튜브 또는 전자 튜브를 인식하고 있습니다. 영국은 그들에게 밸브를 호출합니다.
진공관은 현대의 고체 전자보다 배 EMP 수천을 견딜 수있다. 잘 지어진 튜브 라디오 HEMP를 포함하여 거의 모든 비상 사태를 통해 당신을 얻을 것이다 강화 된 통신 시스템이 될 수 있습니다. 그 어느 고장 있다면, 그것은 대개 작은 기본 튜브 전자 지식을 고정 할 수 있습니다.
아마추어 무선 사업자는 재해시의 통신을 확립하는 것을 제 것으로 알려져있다. 그리고 그들 중 많은 사람들이 진공관 라디오의 사용으로 돌아 간다. 튜브 트랜스미터는 현재 오늘 AC 벽을 실행 정상적으로되지만, 배터리 전원을 위해 그들을 쉽게 설정할 옵션이 있습니다. D-셀 및 9V 배터리조차도 세트 소형 라디오, 임시 전력을 제공 할 수있다.
당신이 깊은 사이클 해양 배터리 고체 상태의 전원 공급 장치를 사용하기로 결정한 경우 단지 우리가 위의 방법을 설명했다처럼 냉동 가방과 호일로 전원 공급 장치를 보호하기 위해 기억합니다. 정상적으로 사용하는 동안 당신은 라디오를 전원 그리드를 사용할 수 있습니다.
오늘 튜브는 여전히 동유럽과 중국에서 제조 한 것입니다. 사실, 기타 앰프 및 하이 엔드 오디오 앰프에 대한 튜브 제조 종류의 미니 붐이 있었다. 그리고 다행히 NOS (새 오래 된 주식) 온라인 쇼핑몰 이베이를 통해 계속 사용할 수 많은 종류의 튜브의 많은이 있습니다. 만큼 물개가 유리와 대부분의 튜브 무한정 지속될 핀 사이에 깨진되지 않습니다.
진공 튜브는 고체 상태 장치가 아닌 EMP에 대한 훨씬 더 강력한, 그러나 EMP에서 튜브 라디오를 보호하기 위해주의해야 할 몇 가지주의 사항이 여전히있다 :
- 사용하지 않을 때는 안테나를 분리합니다. 안테나는 무선 신호에 당긴 할뿐만 아니라 EMP 끌어 당길 것이다. 피뢰기는 돌파에서 핵 EMP를 방지하기 위해 충분하지 않습니다.
- 사용중인 AC 전원하지를 분리합니다. EMP는 안테나처럼 전원 라인을 통해 이동합니다. 사실 그것은 또한 안테나 역할을하므로 AC 전원 코드를 제거하는 것이 가장 좋습니다.
- AC 라인 전압에 의해 구동 라디오은 AC를 DC로 변환하는 정류기가 필요하다. 이전 정류기는 진공관했다 또한 EMP에 저항. 그러나 나중에 모델은 EMP에 취약 깨지기 쉬운 셀레늄 정류기를 사용했다. 그래서 튜브 정류기가 오래된 라디오를 찾습니다.
진공관 송신기 및 라디오에 대해 배울 수있는 가장 좋은 방법은 지역 아마추어 무선 클럽을 통해서이다. 그리고 당신은 더 이상 당신이 멀리 갈 것을 선택하는 경우에 아마추어 무선 사업자 라이센스를 얻기 위해 모스 부호를 배울 필요가 없습니다.
모든 geekiness 제쳐두고, 아마 햄 사업자보다 긴급 통신을위한 더 좋은 자원이 없습니다. 그리고 그들 중 많은 사람들이 당신이 비상 송신기를 설정하는 데 도움이 자신의 전문 지식을 공유하기 위해 기꺼이 것입니다. 또한 주요 후 도움이 될 수있는 전자 교육의 좋은 소스 "이벤트입니다."
What is a HEMP attack? No, it’s not a bunch of hippies smoking pot on your front lawn. HEMP stands for High-Altitude nuclear Electromagnetic Pulse and is an extreme form of EMP. Any strong enough EMP can damage sensitive electronics that we rely on so heavily today.
Sources of EMP
The most common EMP comes from lightning strikes and normal power surges as equipment is turned on and off. Other natural causes, such as solar flares, can also create an EMP. In 1989 the entire electrical grid of Quebec was shut down in about 90 seconds due to a solar flare that hit on the opposite side of the earth.
Modern electronics with microchips are most susceptible, followed by older transistorized circuits. That’s why we have surge suppressors for computers and other sensitive equipment. But most will not protect against a nuclear EMP attack.
EMP damages electronics by overvoltage. The EMP induces an extreme voltage into the conductors of small integrated circuits, causing them to arc and break down. In other words, they get fried.
What many people see as advances in technology also makes us more vulnerable to a HEMP attack. Smaller and more sophisticated electronics are more easily damaged by EMP. And as our society integrates more electronics into everything from the power grid to banking to coffee makers, more of the infrastructure is at risk.
The threat of a HEMP from a nuke is more sinister and dangerous than lightning. When a nuclear weapon is detonated, it produces a very high EMP that spreads like a “wall of energy” and will wipe out anything with solid state electronics over hundreds of miles. Commercial surge suppressors and most military-grade units are not fast enough to stop it. Power lines act as huge antennae to carry the pulse even further, knocking out power grids and electronics that are plugged into the wall socket.
This excerpt from the film TRINITY AND BEYOND, THE ATOMIC BOMB MOVIE shows a few high altitude tests conducted by the United States military shortly before the Limited Test Ban Treaty was signed. It is complete with foreboding, dramatic music and even includes a (simulated?) AM radio cutting out during a detonation.
EMP Protection
So how do you protect against an EMP attack? There are two ways to do it:
- Shield the equipment from the EMP
- Harden the electronics so they aren’t susceptible to EMP
Shielding is the first and easiest line of defense. Sometimes called a Faraday cage, after its inventor, Michael Faraday, an electrically conductive enclosed shield will equalize the electrical charge on the outside, cancelling it on the inside of the shield and protecting the contents.
A true Faraday cage is made of conductive metals, like copper or aluminum or a properly engineered steel enclosure. The inside of a microwave oven is an example of a Faraday cage. But an adequate electromagnetic shield can be made from galvanized steel or aluminum foil. Bare or painted steel doesn’t work, because rust and paint are insulators.
Most safes and file cabinets will not work to shield against EMP. The entire container must be conductive with no breaks in the electrical path. Gaps will “leak” EMP to the inside, making most containers ineffective. Conductive screen or mesh with fine holes will work, though (like the screen on a microwave oven door).
The easiest way to shield small electronics, like a radio or laptop computer, is to place them in a heavy duty zip lock freezer bag, then wrap the whole thing tightly in heavy duty aluminum foil. Be sure to seal any gaps in the foil by folding the seams tightly and be careful to avoid puncturing it to prevent EMP leakage. Thicker foil is more tear resistant, but makes no difference in blocking EMP.
If you do this right, it will work with one layer of each. But for some added insurance add more layers. Add another freezer bag and another layer of foil. Each layer will help to greatly reduce any leakage of EMP if you don’t get it perfectly sealed. Just make sure you alternate layers. If the two layers of foil come in contact, the EMP induced voltage will simply pass from the outer layer to the inner, making the outer layer ineffective.
Testing Your Shield for Leakage
The easiest way to test that you are shielding your device properly is to shield a radio tuned to a strong radio signal. Here are step by step instructions:
Supplies:
- Portable AM/FM radio
- Fresh set of batteries
- 2 or 3 heavy duty freezer bags that fit the radio
- Heavy duty aluminum foil.
You’ll also need a strong radio signal supplied by a radio station (don’t try to do it with other radio sources like your cell phone – it will not work properly with week signals – you want tens of kilowatts or more).
- Install the batteries, make sure the antenna is fully collapsed (in the storage position) and turn the radio on. Start with the FM band.
- Tune the radio to the strongest FM station you can find. If you live in a rural area, you may need to get closer to a station to do this test. Make sure the signal comes in loud and clear with the antenna down.
- Turn the volume up so you will be able to hear the radio through several layers of foil and plastic bags.
- Put the radio in the first freezer bag, fold the bag over tightly and seal it. You should still hear the FM station clearly.
- Next wrap a tight layer of heavy duty aluminum foil around the bagged radio. Make sure the foil sheet is large enough that you can fold the seams at least twice. If you do this right, you should hear the signal drop off to practically nothing.
- If you can still hear the radio clearly, you haven’t sealed the foil effectively. Try again until you get it right and make sure there are no gaps.
- If you are unable to shield it with one layer of foil, add more layers alternating the freezer bags with foil until you get no signal.
After doing the test with an FM station, take everything apart and repeat with a strong AM station. You should get the same result (no signal). It may be harder to shield AM than FM, so don’t get discouraged if you have to add more layers.
Make sure you test both AM and FM (the order doesn’t matter). EMP from a nuke is broadband throughout the RF spectrum, so tuning it to both bands is a better test of real conditions.
After doing your test, unwrap everything and remove the batteries from the radio before sealing it back up. You don’t want find out in an emergency that the batteries leaked and now the radio won’t work.
EMP-Hardened Electronics
So what do you do if you need access to your radio on a regular basis? Obviously you don’t want it wrapped in foil if you use it every day. One option is to simply buy more than one radio. But there is also another option.
The solution might be with old technology: vacuum tubes. If you are old enough to remember the RCA repairman, then you probably recognize vacuum tubes or electron tubes. The British call them valves.
Vacuum tubes can withstand EMP thousands of times higher than modern solid-state electronics. A well-built tube radio can be a hardened communication system that will get you through almost any emergency including a HEMP. And if it ever breaks down, it can usually be fixed with just a little basic tube electronics knowledge.
Ham radio operators are known to be the first ones to establish communication during a disaster. And many of them are returning to the use of vacuum tube radios. Tube transmitters are normally run off AC wall current today, but there are easy options to set them up for battery power. Even a set of D-cell and 9V batteries can provide makeshift power for a small radio .
If you decide to use a solid state power supply with a deep cycle marine battery, just remember to shield the power supply with freezer bags and foil like we showed you above. During normal use you can use the grid to power the radio.
Today tubes are still manufactured in Eastern Europe and China. In fact, there has been a mini-boom of sorts in tube manufacturing for guitar amplifiers and high end audio amps. And fortunately there are large numbers of NOS (New Old Stock) tubes of many kinds still available through online stores and eBay. As long as the seal isn’t broken between the glass and the pins most tubes will last indefinitely.
Vacuum tubes are far more robust against EMP than any solid state device, but there are still a few precautions that need to be taken to protect a tube radio from EMP:
- Disconnect the antenna when not in use. The antenna not only pulls in the radio signal, but it will also pull in an EMP. Lightning arrestors aren’t enough to prevent a nuke EMP from getting through.
- Disconnect the AC power source when not in use. EMP will travel through power lines just like an antenna. In fact it is best to remove the AC power cord as it will also act as an antenna.
- Radios powered by AC line voltage need a rectifier to convert AC to DC. Earlier rectifiers were vacuum tubes and are also resistant to EMP. But later models used fragile selenium rectifiers that are susceptible to EMP. So look for an older radio that has a tube rectifier.
The best way to learn about vacuum tube transmitters and radios is through a local ham radio club. And you no longer have to learn Morse code to get an amateur radio operator license if you choose to go that far.
All geekiness aside, there is probably no better resource for communication in any emergency than ham operators. And many of them will be glad to share their expertise to help you set up an emergency transmitter. They are also a good source of electronics education that could be valuable after a major “event.”