MAIN PASSENGER LIFTS

[전영준]

MAIN PASSENGER LIFTS

Type of Lifts                                        Passenger Lifts – Traditional traction utilising the machine room above.

No. of Lifts                                           Two (Duplex)

Contract Load                                     21 person, 1600 Kgs

Additional Load for

Stone Car Flooring                              200Kgs

Contract Speed                                   1.6 metres/second

Levels Served                                     Six, (Lower Ground, First, Second, Third, Fourth and Fifth)

Stops/Openings                                  6/6 Entrances at front only

Travel Height                                       20.25 metres To Be Confirmed by CONTRACTOR

Supply                                                 400 Volts + 10% - 6% /3/50/4

Internal Car Size                                 1950mm wide x 1750mm deep x 2200mm high

Drive System                                      Traction Machine

Motor Control                                      Closed loop V.V.V.F

Levelling Accuracy                              + 6mm

Starts Per Hour                                   120 starts per hour

Control System                                   Duplex fully collective push button control.

                                                            This system must have the built in facility to operate as a Triplex group with the Scenic Passenger Lifts with out any modifications being required. There will be a switch to control this located in the main security desk.

Lift Equipment Numbers                     All motor room equipment shall be marked with the lift number.

Interconnected Wiring Notice             Provide on each controller.

Switch Functions                                Mark all motor room switches with permanent labels to indicate function.

Emergency Power                              N/A

Fire Alarm                                           Required to shut the lifts down upon actuation of the Building Fire Alarm System, to auto return the lifts to the Ground floor allowing passengers to disembark and then to remain disabled with the doors closed.

Signal Feature linked to                    Provide

Fire Alarm panel                                 

Car Entrances & Doors                     Centre opening automatic doors 1100mm wide x 2100m high clear openings.

Landing Entrances and Doors            As above with small frame architraves, and with 2 hour certified fire rating.

                                                            Brushed stainless steel car and landing doors with  slimline door frames in same finish.

Door Operator Type                           Variable Frequency Automatic operator. Medium usage.

Lift Car Finishes                                 

-          Half wall grey mirror mounted on upper half of rear wall.

-          Side and rear walls fire treated hardwood veneer panels.

-          Brushed finish stainless steel doors, brushed stainless steel finish to front wall and returns.

-          Brushed finish stainless steel skirting 100mm high on each wall.

-          Stainless steel tubular handrails to rear wall.

-          fire treated hardwood veneer panels.

-          Stone flooring (by others allow 50mm recess).

-          Two-way voice communication for emergency communications at all times.

-          Concealed ventilation at high and low level.

-          Protective drapes – one set

-          Drape stud fixings for protection during any goods usage  - both lifts

 

Final finishes to be agreed. Costs to be included in the tender sum for a Mid range car finish

Lighting                                                Concealed fluorescent lighting above ceiling panel, a minimum of 4 No 1500mm fluorescent lamps. Include for 3 hour non maintained emergency lighting.

Car Operating Panel                           Include within car side wall and suitable for disabled users in brushed stainless steel.

Car Door Protection                            Mechanical door protection plus full height infra red  electronic door detector with high density beam pattern.

Car and Landing Sills                          Extruded Aluminium Section

(Include Full Width Landing Cill Support)

Top of Car Guard Rails                       Fit to the rear of each car.

Buffers                                                            Energy Dissipation

Full Fascias                                        Include between the headers to sills.

Guide and Entrance Fixings               Include for fixings to lift shaft steelwork by others.

Pit Ladder                                            Provide and fix in pit.

Machine plinth ladder/rails                  N/A

Machine Guards                                  Supply and fit.

Lift Supplies                                        An 8 way single phase fuse board complete with RCD protected ways will be provided by others

Items indicated below to be connected to standard MCB’s on the above board.

§         Car lights

§         Shaft lights

§         Motor room heater

Items indicated below to be connected to RCD MCB’s of the above board.

§         Motor room socket outlet

§         Pit socket outlet

M/R Socket                                          Included in the works for the Scenic lift

Shaft Lighting  in each shaft               Supply and install 1500mm vapour proof fluorescent fittings to provide 50 lux anywhere in the shaft including a fitting 500mm from the top and the bottom of the shaft complete with 2 way switching in the machine room and pit level. This circuit to be fed from the motor room fuse board.

Motor Room Lighting                           By others

Isolator Switch                                                By others it will be a 3 phase and neutral Switch Fuse in the motor room – fuse size to be determined by CONTRACTOR - for each lift.

M/R Heating                                        Included in the works for the Scenic lift                                                 

Emergency Lighting                            Provide one unit above each hoist unit.

Pit Stop Switch                                   Include

Pit Socket Outlet                                 Include to Pit. Twin metal clad socket fed from a RCD way on the above fuse board.

Intercom Unit                                       N/A

Car Ventilation                         Centrifugal extract fan to the car roof controlled by a thermostat

Motor Room Ventilation                       By Others

Sound Isolation Machine/Car              Include

Signals            Car:                             Call Accepted Pushes

Alarm Push

Door Open Push

Car Preference Key Switch (Goods Control) – both lifts

L.C.D floor and direction indicator set above the car operating panel and clearly visible for any passenger within the lift car.

Landing:                      Call Accepted Pushes. Halo illumination.

Direction Indicators – at each floor level. Complete with Bi-Directional gongs.

Landing position indicator at every floor for each lift – L..C.D type

Note:                                                    All buttons to be tactile, illuminating micro movement in stainless steel. 

                                                            All faceplates to be vandal proof screw fixings.

Voice Communication to lift car          Include within the lift car for an automatic hands free auto-dial telephone system discretely mounted, with anti nuisance delay on alarm push.

                                                            Unit must have voice function and be fully compliant with EN81:1 1998 and GOST R Standards.

                                                            Manufacture to be third party type only

Telephone socket                               CONTRACTOR to connect to new auto-dialler.

Lifting Beam                                        CONTRACTOR to provide

Lift Shaft Smoke Detector                  CONTRACTOR to provide

Shaft Smoke Vent                               CONTRACTOR to provide

Alarm System                                     Alarm bell shall be fitted within the lift shaft at Ground Floor Level and also the provision of volt free contacts within the machine room, to be connected to a remote alarm system by CONTRACTOR.

Safety Gear                                         Bi- Directional Safety Gear operated via a Bi-Directional overspeed governor.

Additional Items                                   Audible floor Level Indicator system for emergency release.

                                                            Controller rubber mat. 

Emergency stop switches adjacent to each gearbox..

All relevant notices, including:

                                                           Hand winding procedure.

Record Drawings                                Include.2 sets

Wiring Diagrams                                 Include. One set of encapsulated Schematic wiring diagrams.

Operating & Maintenance                   Include.2 sets

Manuals                                              

Maintenance                                       Include for 12 monthly maintenance visits.

                                                            Callout coverage to be normal working hours